Gw-instek GOM-802 Programming Manual Manuale Utente Pagina 27
- Pagina / 27
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
DC MILLI-OHM METER
PROGRAMMER MANUAL
⎯ 52 ⎯
Queues
The output queue is included to power supplies.
Output Queue: The METER store query responses in the output queue by
succeeding the IEEE 488.2 protocol. If the METER receives a new
command or query message after a message terminator, the METER will
clear and reset this queue each time. The computer must read a query
response before it sends the next command (or query) or it loses response
to earlier queries.
Error/Event Queues
When an error or event occurs, the output queue stores the message. The
output queue stores and reports the messages on a FIFO (first in first out)
state. The SYSTem:ERRor? query reads the next item from the output
queue. If output queue overflows, the error message is –350, “Queue
overflow”; the queue can’t store or report succeeding messages till it
is read or cleared.
Error Message
Table 8 lists the SCPI error messages for the METER.
Table 8 The error messages for the METER:
SCPI Error Code and Description SESR Bit
0, “No error”
-100, “Command error” 5
-200, “Execution Error” 4
-221, “Settings conflict” 4
-222, “Data out of range” 4
-350, “Queue overflow” 3
-410, “Query INTERRUPTED” 2
-420, “Query UNTERMINATED” 2
-430, “Query DEADLOCKED” 2
DC MILLI-OHM METER
PROGRAMMER MANUAL
⎯ 53 ⎯
- 1. INTRODUCTION 1
- III. Turn on the Meter 2
- IV. Turn on the computer 2
- THE METER VIA RS232 INTERFACE 3
- 4. INPUT AND OUTPUT QUEUE 5
- 5. COMMANDS AND SYNTAX 5
- I. GPIB message terminators 7
- DC MILLI-OHM METER 10
- PROGRAMMER MANUAL 10
- *CLS (no query form) 11
- *ESR? (query only) 12
- *IDN? (query only) 12
- *RST (no query form) 12
- :CONFigure:AUTo 13
- *STB? (query only) 13
- *WAI (no query form) 13
- :CONFigure:RANGe?(query only) 14
- Set the temperature function 15
- :CONFigure:SPEed 16
- :CONFigure:SCAN:STATe 16
- :CONFigure:SCAN:CHANnel 16
- :CONFigure:SCAN:DELay 17
- :CONFigure:BUZZer 17
- :CONFigure:TRIGger 17
- Returns limit result 19
- STATus:OPERation:ENABle 21
- STATus:PRESet 21
- STATus:QUEStionable:ENABle 22
- SYSTem:ERRor? (query only) 22
- SYSTem:VERSion? (query only) 23
- 7. STATUS AND ERROR REPORTING 23
- Structure of System 23
- Status Registers 23
- QUEStionable Status 24
- OPERation Status 24
- Status Byte Register 24
Prodotti e manuali riguardandi Apparecchiature Gw-instek GOM-802 Programming Manual
Apparecchiature Gw-instek GDM-398 Manuale Utente
(75 pagine)
(75 pagine)
AirLink Tarjetas de red manuales de usuario
La lista de productos de AirLink Tarjetas de red contiene 6 manuales de usuario para 6 seleccionados. Todas las guías de usuario en pdf están disponibles para descargar o ver en línea.
Commenti su questo manuale