Gw-instek GSP-930 Programming Manual Manuale Utente Pagina 38
- Pagina / 195
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
GSP-930 Programming Manual
36
Query
A query is a simple or
compound command
followed by a question mark
(?). A parameter (data) is
returned.
Example
CALCulate:CSO:STATe?
Compound
Two or more commands on
the same command line.
Compound commands are
separated with either a semi-
colon (;) or a semi-colon and a
colon (;:).
A semi-colon is used to join
two related commands, with
the caveat that the last
command must begin at the
last node of the first
command.
A semi-colon and colon are
used to combine two
commands from different
nodes.
Example
calc:ctb:stat on;result?
- Spectrum Analyzer 1
- Table of Contents 3
- SAFETY INSTRUCTIONS 4
- Safety Guidelines 5
- GETTING STARTED 9
- GSP-930 Introduction 10
- Accessories 12
- Package Contents 13
- Appearance 14
- RF INPUT 50 17
- +30dBm MAX 17
- MAX.DC ±50V 17
- REV PWR +30dBm 18
- TG OUTPUT 50 18
- AC 100 240V 19
- 50 60 Hz 82W MAX 19
- Status Icon Overview 23
- REMOTE CONTROL 25
- Interface Configuration 26
- Password 29
- Configure RS232C 31
- Command Syntax 37
- 2 , filename.cor 39
- 1 2 3 4 5 39
- Status Registers 42
- REMOTE CONTROL 43
- Condition register 44
- Event Register 44
- Event Enable Register 44
- Status Byte Register (STB) 45
- Operation Status Register 47
- Questionable Status Register 47
- Command List 51
- SCPI Commands 61
- CALCulate Commands 64
- :CALCulate:ACPR:CHPower? 68
- :CALCulate:ACPR:STATe 69
- :CALCulate:CNR:RESult? 69
- :CALCulate:CNR:STATe 69
- :CALCulate:CSO:RESult? 70
- :CALCulate:CSO:STATe 70
- :CALCulate:CTB:RESult? 71
- :CALCulate:CTB:STATe 71
- :CALCulate:CTB:RESTart 71
- :CALCulate:DEMod:AM:STATe 74
- :CALCulate:DEMod:FM:STATe 76
- :CALCulate:DEMod:RESet 77
- :CALCulate:JITTer:STATe 77
- :CALCulate:JITTer:PHASe? 78
- :CALCulate:JITTer:TIME? 78
- :CALCulate:LIMit:FAIL? 79
- :CALCulate:LIMit:LOW 79
- :CALCulate:LIMit:HIGH 79
- :CALCulate:LIMit:PASS:MODE 80
- :CALCulate:LIMit:STATe 80
- :CALCulate:MARKer:AOFF 81
- RESolution 81
- RESolution:AUTO 82
- :CALCulate:MARKer:PEAK:DATA? 85
- :CALCulate:MARKer<n>:X 89
- :CALCulate:MATH:PDIF 90
- :CALCulate:MATH:LDIF 90
- :CALCulate:MATH:LOFF 91
- :CALCulate:NDB:STATe 91
- :CALCulate:NORMalize:STATe 92
- :CALCulate:OCBW:STATe 92
- :CALCulate:OCBW:CHPower? 93
- :CALCulate:OCBW:POWer? 93
- :CALCulate:PMETer:POWer? 93
- :CALCulate:SEM:STATe 94
- :CALCulate:TOI:DIFFerential? 95
- :CALCulate:TOI:LIMit:STATe 96
- :CALCulate:TOI:RESult? 96
- :CALCulate:TOI:STATe 97
- CONFigure Commands 97
- :CONFigure:MODE 97
- DISPlay Commands 98
- :DISPlay:BRIGhtness 99
- :DISPlay:ENABle 99
- [:SCALe]:AUTO 99
- [:SCALe]:PDIVision 100
- [:SCALe]:RPOSition 100
- [:SCALe]:RVALue 102
- :DISPlay[:WINDow]:NORMal 102
- ALTernate 103
- :DISPlay[:WINDow]:SPLit:TOPO 104
- :DISPlay[:WINDow]:TOPO 104
- NRLevel 105
- INITiate Commands 109
- :INITiate:CONTinuous 109
- :INITiate[:IMMediate] 109
- INPut Commands 110
- :INPut:ATTenuation 110
- :INPut:ATTenuation:AUTO 110
- :INPut:IMPedance 111
- :INPut:OFFSet 111
- MMEMory Commands 112
- :MMEMory:CATalog? 112
- :MMEMory:CDIRectory 113
- :MMEMory:COPY 113
- :MMEMory:DELete 114
- :MMEMory:DESTination 114
- :MMEMory:LOAD:CORRection 115
- :MMEMory:LOAD:LIMit 115
- :MMEMory:LOAD:PMETer 115
- :MMEMory:LOAD:SEQuence 115
- :MMEMory:LOAD:STATe 116
- :MMEMory:LOAD:TRACe 116
- :MMEMory:MOVE 116
- :MMEMory:REName 117
- :MMEMory:STORe:CORRection 117
- :MMEMory:STORe:LIMit 117
- :MMEMory:STORe:PMETer 117
- :MMEMory:STORe:SCReen 118
- :MMEMory:STORe:SEQuence 118
- :MMEMory:STORe:STATe 118
- :MMEMory:STORe:TRACe 119
- OUTPut Commands 119
- :OUTPut[:STATe] 119
- SENSe Commands 120
- [:SENSe]:ACPR:HLIMit 124
- [:SENSe]:ACPR:LLIMit 125
- [:SENSe]:ACPR:HELP:STATe 125
- [:SENSe]:ACPR:SPACe 125
- [:SENSe]:ASET:AMPLitude 126
- [:SENSe]:ASET:AMPLitude:AUTO 126
- [:SENSe]:ASET:RUN 126
- [:SENSe]:ASET:SPAN 127
- [:SENSe]:ASET:SPAN:AUTO 127
- [:SENSe]:AVERage:COUNt 127
- [:SENSe]:AVERage:STATe 128
- [:SENSe]:AVERage:TYPE 128
- [:SENSe]:BANDwidth 129
- [:RESolution]:AUTO 129
- [:SENSe]:CHANnel:SPACe:DOWN 130
- [:SENSe]:CHANnel:SPACe:UP 130
- [:SENSe]:CNR:CHANnel:SPACe 130
- [:SENSe]:CSO:CHANnel:SPACe 132
- [:SENSe]:CTB:CHANnel:SPACe 133
- [:SENSe]:DEMod:EARPhone:TYPE 133
- [:SENSe]:DEMod:EARPhone:GAIN 134
- [:SENSe]:DEMod:IFBW 135
- [:SENSe]:DETector[:FUNCtion] 135
- [:SENSe]:EMIFilter:STATe 136
- [:RESolution] 136
- [:SENSe]:FREQuency:CENTer 137
- [:SENSe]:FREQuency:OFFSet 138
- [:SENSe]:FREQuency:SPAN 138
- [:SENSe]:FREQuency:SPAN:FULL 138
- [:SENSe]:FREQuency:STARt 139
- [:SENSe]:FREQuency:STOP 139
- [:SENSe]:JITTer:OFFSet:STARt 139
- [:SENSe]:JITTer:OFFSet:STOP 140
- [:SENSe]:OCBW:PERCent 141
- [:SENSe]:OCBW:SPACe 141
- [:SENSe]:PMETer:FREQuency 141
- [:SENSe]:PMETer:HLIMit 142
- [:SENSe]:PMETer:HOLD:STATe 142
- [:SENSe]:PMETer:LLIMit 142
- [:SENSe]:POWer[:RF]:GAIN 144
- INTegration 144
- [:SENSe]:SEMask:CARRier:AUTO 145
- [:SENSe]:SEMask:CARRier:CPSD 146
- [:SENSe]:SEMask:HELP:STATe 147
- BANDwidth 148
- FREQuency:STARt? 150
- FREQuency:STOP? 150
- WIDth[:RESolution]:AUTO 152
- :ABSolute 154
- ABSolute:COUPle 154
- RELative 155
- RELative:COUPle 155
- [:SENSe]:SEMask:SELect 156
- [:SENSe]:SEMask:TYPE 157
- MOPower 158
- [:SENSe]:SWEep:EGATe:DELay 161
- [:SENSe]:SWEep:EGATe:LENGth 161
- [:SENSe]:SWEep:EGATe:STATe 162
- [:SENSe]:SWEep:TIME 162
- [:SENSe]:SWEep:TIME:AUTO 162
- [:SENSe]:TOI:REFerence 163
- [:SENSe]:TOI:LIMit 163
- SOURce Commands 163
- [:AMPLitude] 164
- [:AMPLitude]:OFFSet 164
- [:AMPLitude]:STEP 165
- [:AMPLitude]:STEP:AUTO 165
- :SOURce:POWer:MODE 165
- :SOURce:POWer:SWEep 166
- SYSTem Commands 167
- :SYSTem:ALARm:STATe 167
- :SYSTem:CLOCk<n>:DATE 168
- :SYSTem:CLOCk<n>:MODE 168
- :SYSTem:CLOCk<n>:STATe 168
- :SYSTem:CLOCk<n>:TIME 169
- :ADDRess 169
- :SYSTem:COMMunicate:LANReset 169
- :SYSTem:COMMunicate:USB:MODE 170
- :SYSTem:DATE 170
- :SYSTem:ERRor:CLEar 170
- :SYSTem:ERRor[:NEXT]? 171
- :SYSTem:KLOCk 171
- :SYSTem:PRESet 171
- :SYSTem:PRESet:TYPE 171
- :SYSTem:PRESet:USER:SAVE 171
- :SYSTem:REBoot 172
- :SYSTem:SHUTdown 172
- :SYSTem:TIME 172
- :SYSTem:UPDate 172
- :SYSTem:VERSion:HARDware? 173
- :SYSTem:VERSion:SOFTware? 173
- STATus Commands 174
- :STATus:OPERation:CONDition? 174
- :STATus:OPERation:ENABle 175
- :STATus:OPERation[:EVENt]? 175
- :STATus:QUEStionable:ENABle 177
- CONDition? 179
- [:EVENt]? 180
- NTRansition 180
- PTRansition 181
- :CONDition? 184
- :NTRansition 185
- :STATus:PRESet 189
- TRACe Commands 189
- :TRACe[:DATA]? 189
- TRIGger Commands 190
- :TRIGger[:SEQuence]:DELay 190
- :TRIGger[:SEQuence]:MODE 192
- :TRIGger[:SEQuence]:SOURce 193
- UNIT Commands 195
- :UNIT:PMETer:POWer 195
- :UNIT:POWer 195
Prodotti e manuali riguardandi Apparecchiature Gw-instek GSP-930 Programming Manual
Apparecchiature Gw-instek PEL-300 Manuale Utente
(41 pagine)
(41 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale